17.080 时间、速度、加速度、角速度的测量 标准查询与下载

GSO ISO 17713-1:2009 气象学 风测量 第1部分：旋转风速计性能的风洞测试方法

1.1 This part of ISO 17713 describes wind tunnel test methods for determining performance characteristics of rotating anemometers, specifically cup anemometers and propeller anemometers. 1.2 This part of ISO 17713 describes an acceptance test and unambiguous methods for measuring the starting threshold, distance constant, transfer function and off-axis response of a rotating anemometer in a wind tunnel. Note that when transferring values determined by these methods to atmospheric flow, there is a difference between anemometer performance in the free atmosphere and in the wind tunnel.

Meteorology - Wind measurements - Part 1: Wind tunnel test methods for rotating anemometer performance

ANSI/IEEE 836:2009 线性加速度计精密离心机试验的推荐实施规程

This recommended practice provides a guide to the conduct and analysis of precision centrifuge tests of linear accelerometers, covering each phase of the tests, beginning with the planning.

Recommended Practice for Precision Centrifuge Testing of Linear Accelerometers

ANSI/IEEE 1139:2008 基本频率和时间计量学用物理量标准定义.随机不稳定性

This standard covers the fundamental metrology for describing random instabilities of importance to frequency and time metrology. Quantities covered include frequency, amplitude, and phase instabilities; spectral densities of frequency, amplitude, and phase fluctuations; and time-domain deviations of frequency fluctuations.

Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology - Random Instabilities

ANSI/IEEE 1293/Cor1:2008 线性单轴非回转仪加速计用标准规范格式指南和试验程序.技术勘误1:附录K&L变化

Standard Specification Format Guide and Test Procedure for Linear, Single-Axis, Non-Gyroscopic Accelerometers - Corrigendum 1: Annex K & L Changes

IEEE 1293/COR 1-2008 线性、单轴、无回旋装置加速度计的规范格式指南和试验程序.技术勘误1:附件K和附件L的改变

Specification format guide and test procedure for linear, single-axis, nongyroscopic accelerometers; Corrigendum 1: Changes to annex K and annex L

SANS 1795-5:2007 公路交通执法系统．第5部分：公路交通执法用数据捕捉和记录设备

Specifies mechanical, electrical and operational requirements for data capturing and recording equipment that is intended for road traffic law enforcement and prosecution purposes.

Road traffic law enforcement systems Part 5: Data capturing and recording devices for road traffic law enforcement

SANS 1795-2:2007 公路交通执法系统．第2部分：雷达测速装置

Specifies mechanical, electrical and operational requirements for radar speed measuring equipment that is intended for traffic law enforcement and prosecution purposes.

Road traffic law enforcement systems Part 2: Radar speed measuring equipment

SANS 1795-4:2007 公路交通执法系统．第4部分：时间距离比测速装置（变量距离/变量时间）

Specifies mechanical, electrical and operational requirements for mobile speed measuring equipment that is installed in an observer vehicle, that calculates speed based on measurements of distance and time, and that is intended for traffic law enforcemen

Road traffic law enforcement systems Part 4: Distance-over-time speed measuring equipment (variable distance/variable time)

SANS 1795-0:2007 公路交通执法系统．第0部分：一般要求

Specifies mechanical, electrical and operational requirements for speed measuring equipment and associated speed measuring systems that are intended for traffic law enforcement and prosecution purposes.

Road traffic law enforcement systems Part 0: General requirements

SANS 1795-3:2007 公路交通执法系统．第3部分：时间距离比测速装置（固定距离/变量时间）

Specifies mechanical, electrical and operational requirements for distance-over-time speed measuring equipment (fixed distance/variable time) that is intended for traffic law enforcement and prosecution purposes.

Road traffic law enforcement systems Part 3: Distance-over-time speed measuring equipment (fixed distance/variable time)

GEIA-HB-927-2007 复杂系统共同数据模式执行指南

This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer.

Implementation Guide for Common Data Schema for Complex Systems

GEIA-STD-927-2007 复杂的系统获得相辅相成常见的数据模式

GEIA-STD-927 specifies the data concepts to be exchanged to share product information pertaining to a complex system from the viewpoints of multiple disciplines. It supports the exchange of data across the entire life cycle for the product from the conc

Common Data Schema for Complex Systems To obtain one complimentary of GEIA-STD-927

GEIA EIA-836A-2007 配置管理数据交换和交互操作以补充不足

EIA-836 logically extends the Configuration Management (CM) principles of ANSI/EIA 649. It provides for interoperability between trading partners by establishing a common language for the exchange of data between dissimilar databases.

Configuration Management Data Exchange and Interoperability

GEIA PN-GEIA-STD-0007-2006 物流产品数据.版本1.0 GEIA-STD-0007出版

This standard applies to the interconnection of data terminal equipment and numerical control equipment at the tape reader interface. The data terminal would typically be connected to a remote data source/sink such as a computer.

Logistics Product Data Version 1.0; To be published as GEIA-STD-0007

GEIA EIA 557-B-2006 统计过程控制系统

Continuous quality improvement and the achievement of operational and manufacturing excellence are the essence of the total quality philosophy.

STATISTICAL PROCESS CONTROL SYSTEMS [Replaced: JEDEC EIA-557-A]

VDI/VDE 2646-2006 扭矩测量装置 校准的最低要求

The present guideline is generally applicable for torque measurement devices, the torque of which is defined by measuring of the elastic form change of a deformation body or a measured variable which is in proportion to the torque. This guideline is applicable for the progressive (static) and continuous (quasi-static) calibration of torque measurement devices. Among other things, torque measurement devices for the static calibration of test equipment and torque measurement devices for general applications (e.g. as torque sensors in power screwdrivers or torque transducers in test benches) are the subject. Procedures for the calibration (so-called work calibrations) and for the definition of the measuring uncertainty are given.

Torque measuring devices - Minimum requirements in calibrations

GEIA-HB-859-2006 数据管理的实施指南

ata management is an area of discipline oriented to ensuring that data and information are available and usable when and where they are needed. Data management is most visibly practiced in challenging information environments-those in which the volume o

Implementation Guide for Data Management

ANSI/IEEE 1554-200x:2005 惯性传感器试验设备、仪器、数据获取和分析的推荐实施规程

Recommended practices for gyroscope and accelerometer testing are discussed, ranging from the equipment and instrumentation employed to the way that tests are carried out and data are acquired and analyzed. Recommendations are made on techniques for acquisition, filtering, storage, and analysis of the test data in keeping with modern practice.

Recommended Practice for Inertial Sensor Test Equipment, Instrumentation, Data Acquisition, and Analysis

ANSI/IEEE 1554:2005 惯性传感器试验设备、仪器、数据获取和分析的推荐实施规程

Recommended practices for gyroscope and accelerometer testing are discussed, ranging from the equipment and instrumentation employed to the way that tests are carried out and data are acquired and analyzed. Recommendations are made on techniques for acquisition, filtering, storage, and analysis of the test data in keeping with modern practice.

Recommended Practice for Inertial Sensor Test Equipment, Instrumentation, Data Acquisition, and Analysis

KS G 8011-2004(2009) 节拍器

Metronomes