P26 金属结构工程 标准查询与下载
共找到 507 条与 金属结构工程 相关的标准，共 34 页
本工程适用于一般工业与民用建筑所采用的以受弯为主的波纹腹板钢构件或波纹腹板钢混凝土组合构件。
Technical specification for steel structures with corrugated webs
- ICS
- CCS
- P26
- 发布
- 2011-05-31
- 实施
- 2011-09-01
1 本文规定了建筑结构用离心工艺制造铸钢管的牌号表示法、技术要求、制造工艺与交货状态、试验方法、检验规则及标识、包装和质量证明书等。 2 本标准适用于离心铸造工艺生产的铸钢管（以下简称铸钢管），产品主要用于建筑钢结构，塔栀结构与桥梁结构等。
Casting steel tubes for building structures
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011-05-09
- 实施
- 2011-10-01
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 4-2: Tanks
- ICS
- 23.020.10;91.010.30;91.080.10
- CCS
- P26
- 发布
- 2011-05
- 实施
Technical specification for light steel frame fixed formwork shear wall structure
- ICS
- CCS
- P26
- 发布
- 2011-03-01
- 实施
- 2011-03-01
本规程适用于以冷弯薄壁型钢为主要承重构件，层数不大于3层，檐口高度不大于12m的低层房屋建筑的设计、施工及验收。
Technical specification for low-rise cold-formed thin-walled steel buildings
- ICS
- CCS
- P26
- 发布
- 2011-01-28
- 实施
- 2011-12-01
This test method evaluates the ability of a non-combustible passive fire protection system installed on structural divisions on commercial ships to function after shock loading. The shock loading is accomplished by conducting impact testing of a test specimen consisting of insulation on a standard steel or aluminum structural core installed on a medium weight shock test machine. Following the shock testing the shocked test specimen and an unshocked test specimen are tested for fire resistance. Both shocked and unshocked test specimens are installed side-by-side in a fixture and fire tested at the same time. The fire resistance for both specimens is measured and recorded. Other passive fire protection systems using the same insulation materials and attachment methods and having lower fire resistance ratings will be accepted without additional shock testing.1.1 The purpose of the specification is to evaluate insulation installed on steel or aluminum structural division as defined in IMO resolution A.754 (18) to ensure the insulation is not degraded in the event of a shock. 1.2 The non-combustible passive fire protection insulation shall be installed, which will meet the highest level of commercial fire resistance expected. Lower levels of fire resistance will be allowed without additional shock testing. 1.3 This test method is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products or assemblies under actual fire conditions. 1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Shock Testing of Structural Insulation of a Class Divisions Constructed of Steel or Aluminum
- ICS
- 47.020.85
- CCS
- P26
- 发布
- 2011
- 实施
1.1 This specification covers nonstructural steel framing members in interior construction assemblies. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Nonstructural Steel Framing Members
- ICS
- 91.060.10 (Walls. Partitions. Facades)
- CCS
- P26
- 发布
- 2011
- 实施
1.1 This specification covers nonstructural steel framing members in interior construction assemblies. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Nonstructural Steel Framing Members
- ICS
- 91.060.10 (Walls. Partitions. Facades)
- CCS
- P26
- 发布
- 2011
- 实施
Provides design methods for determining the strength [resistance] and stiffness of cold-formed steel nonstructural members that are not a part of the gravity and lateral load resistance systems.
North American Standard for Cold-Formed Steel Framing - Nonstructural Members
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011
- 实施
SDI-T-CD-2011 is a new standard for structural testing of composite steel deck-slabs to be used by designers, specifiers, manufacturers, and installers of composite steeldeck slabs. The specification sets guidelines and requirements relating to methodsfor structural testing of composite steel deck slabs. Non-mandatory user notes andcommentary are included for further clarification and guidance.
Test Standard for Composite Steel Deck-Slabs
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011
- 实施
1.1 This specification covers the minimum requirements for the installation of interior nonstructural steel framing and furring members designed to receive screw-attached gypsum panel products. The steel framing and furring members covered in this specification are limited to those complying with Specification C645. 1.2 Details of construction for a specific assembly to achieve the required fire resistance, sound or acoustic rating shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing, sound or acoustic laboratories. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products
- ICS
- 91.100.10 (Cement. Gypsum. Lime. Mortar)
- CCS
- P26
- 发布
- 2011
- 实施
This standard establishes safety requirements for the erecting, handling, fitting, fastening, reinforcing and dismantling of structural steel, plate steel, steel joist, and metal deck at a final in-place field site during construction, maintenance and dismantling operations.
Safety Requirements for Steel Erection
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011
- 实施
1.1 This specification covers steel studs, runners (tracks), and bracing or bridging (with a base steel minimum thickness of not less than 0.0329 in. (0.836 mm)) for screw application of gypsum panel products and metal plaster bases in load-bearing (transverse and axial) construction assemblies. Steel of lesser thickness shall be permitted in additional engineered products. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Load-Bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases
- ICS
- 91.060.10 (Walls. Partitions. Facades)
- CCS
- P26
- 发布
- 2011
- 实施
Provides a new standard for quality control and quality assurance for installation of steel deck to be used by designers, specifiers, manufacturers, and installers of steel deck used in floors and roofs. The specification sets guidelines and requirements for quality control and quality assurance for installation of steel deck. Non-mandatory user notes and commentary are included for further clarification and guidance.
Standard for Quality Control and Quality Assurance for Installation of Steel Deck
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011
- 实施
In the absence of specific instructions to the contrary in the contract documents, the trade practice defined in this Code of Standard Practice would govern the design, fabrication and installation of cold-formed steel structural framing.
Code of Standard Practice for Cold-Formed Steel Structural Framing
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2011
- 实施
National Annex - Nationally determined parameters - Eurocode 9: Design of aluminium structures - Part 1-5: Shell structures
- ICS
- 91.010.30;91.080.10
- CCS
- P26
- 发布
- 2010-12-01
- 实施
National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels
- ICS
- 91.010.30;91.080.10
- CCS
- P26
- 发布
- 2010-12-01
- 实施
National Annex - Nationally determined parameters - Eurocode 3: Design of steel Structures - Part 1-7: Plated structures subject to out of plane loading
- ICS
- 91.010.30;91.080.10
- CCS
- P26
- 发布
- 2010-12
- 实施
National Annex - Nationally determined parameters - Eurocode 9: Design of aluminium structures - Part 1-1: General rules
- ICS
- 91.010.30;91.080.10
- CCS
- P26
- 发布
- 2010-12
- 实施
Eurocode 3: Design of steel structures - Part 1-10: Material toughness and through-thickness properties; German version EN 1993-1-10:2005 + AC:2009
- ICS
- 91.010.30;91.080.10
- CCS
- P26
- 发布
- 2010-12
- 实施
